Wepoint Pultruded Cooling Towers

PULTRUDED COOLING TOWERS

Salient Features

• Designed for maximum service life dependability and performance
• Readily adoptable for industrial processes, DG sets & Air conditioning
• Designed for unifom water distribution and optimal heat transfer
• Consumes minimum power due to high efficiency of Axial flow fan sets.

Structure :
The Structure of Cooling tower is fabricated of Pultruted FRP profile which are free from corrosion. The whole cooling tower is fabricated in pieces & bolted together to facilitate easy shifting

 

Casing & Sump
The tower casing is made of FRP which encloses the surface area serves to isolate air stream, which passes over the surface area.The casing shape is of curtain type which reduce frictional resistance of air and aid air flow pattern.
The sump serves the purposes of collecting the water descending from the surface area and channelling it to the suction point. Further the sump also acts as a reservoir of water. The sump is also made of FRP and has similar characteristics as the casing.
 

Louvers
Louvers are in FRP are provided to prevent contaminants like leaves, birds etc. entering the cooling tower & to facilitate the air entry in to the tower.

  

Hot water Basin
In cross flow induced draughtcooling tower the FRP Hot Water Basin is used to distribute the water evenly over the cross section of the tower.
 

Distribution Box
The distribution box serve the pupose of channeling the hot water to spread all over the fill area evenly to provide maximum efficiency of the cooling tower
 

Flower Nozzle
The PVC Flower nozzles are used in hot water basin to sprinkler water all over the splash bar area & operates under gravity

Header & Sub Header Pipes
In counter flow induced draught cooling tower the PVC header pipes & sub-header pipes are used to distribute the water evenly over the cross section of the tower.

 

PVC Nozzle
The PVC Ring type nozzles are used in sub-header pipes to sprinkler water all over the fill area & operates under gravity
 

Fan Cylinder
In cross flow induced draught cooling tower the fan cylinder is made of Hot dip galvanized MS structure covered with fiber glass reinforced plastic and has sufficient structural strength to withstand high wind velocity & vibrations emanating from the motor and other equipment. Cylinder has a high impact resistance and even if damaged is easily repaired at site. The cylinder is in sections of easy to handle sizes and is assembled at site using bolting joints
In Counter flow induced draught cooling tower the fan cylinder is made of tough fiber glass reinforced plastic and has sufficient structural strength to withstand high wind velocity & vibrations emanating from the motor and other equipment FRP cylinder has a high impact resistance when laminated with lsopathalic Resin and even if damaged is easily repaired at site. The cylinder is in sections of easy to handle sizes and is assembled at site using bolting joints
 

Splash Bars
In cross flow induced draught cooling tower splash bars are used. The Splash Bars section is designed to bring intimate contact of water and air so as to facilitate heat and mass tranfer at the same time aiding in proper and even distribution of air and water over the cross sections, while maintaining minimum pressure drop. The Splash Bars are of C section and perforated from virgin PVC for excellent resistance to corrosion and give maximum area wettage.
 

Grid System
Splash bars are supported on SS304 grids which assures positive & permannent positioning & allow splash bar to stay on its sting with the help of PVC tie clip
 

PVC Fills
PVC Honey comb double edge folded fills are used in counter flow induced draught cooling tower. The fills section is designed to bring intimate contact of water and air so as to facilitate heat and mass tranfer at the same time aiding in proper and even distribution of air and water over the cross sections, while maintaining minimum pressure drop. The fills are of honeycomb section and are vacuum formed from virgin PVC for excellent resistance to corrosion and give maximum area wettage.

Drift Eliminators
Drift Eliminators, made out of UV resistant rigid PVC, are designed to remove entrained particles from air stream efficiently, with minimum pressure drop, thereby reducing the fan power requirement when the air passes through the Drift Eliminator.
Cross flow tower applications, the almost vertical water conduits provided by drift eliminator remove the water droplets out of the drift eliminator area and return them back into the tower and does not allow any re-entry. The special locking pin arrangement facilitates quick and simple assembly at site.
 

Fan
The Aluminium fan is an axial flow, multiblade version with blade section and adjustable blade pitch. The fan is designed to deliver large volumes of air at low power consumption and low noise generation. The fans are dynamically balanced for smooth operation, longer bearing and more life including that of the supporting structure.
 

FAN DRIVE MOTOR
The fan drive motor is in IP55 weather proof design. The fan is directly driven by the special extended shaft motor made from EN8 steel mounted facing downward on a mounting frame on the top of the Cooling Tower.
 

 L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com

 

 

 

 

 

 

 

 

 

 

 

 

Cooling Tower for Heat Exchanger

Salient Features

• Designed for uniform water distribution and optimal heat transfer.
• The special characteristic of fiber-reinforced plastic provide excellent resistance to corrosion.
• These cooling towers are compact and light in weight.
• These cooling towers offer easy installation and maintenance.

Casing :
The tower casing is made of tough fibre-glass reinforced plastic (FRP) and has sufficient structure strength to withstand high wind velocities and vibrations. UV - stabilized resin is used along with gel coat for longer life.it is resistant to local impact and even if slight damage occurs, local repairs can easily be done. The portion of casing housing fill and eliminator has a round cross section. The water collection sump, also of FRP, is leak proof and avoids water spillage.

PVC Fills
The fill is of rigid Polyvinyl Chloride (PVC) and is of honeycomb design with very large contact surface area. The fill splits the air and water into several streams, increasing the time of contact and also heat transfer between water and air. The fill is in modules and is packed in the tower casing without ant cutting for curves. The air pressure drop through the fill is negligible. The fills are available with flute height of 12mm and 19mm with sheet thickness of 0.15 mm and 0.20 mm .
 

Sprinkler
Automatic rotary sprinkler system made of Aluminum alloy or cast steel material, with rotary head and sprinkler pipe distributes the hot water over the entire space of the filler. Sprinkler pipes are non-clogging, require low pressure to operate and assures uniform water flow with minimal operating pump head. The FRP eliminators attached to sprinkler pipe are specifically designed for low pressure drop and minimizes the drift loss of water.

 

Axial Fan
Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen are non- corrosive of plastic, FRP or aluminum alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is adjustable and dynamically balanced.
 

Motors
The motors are totally enclosed (IP55), Flange type , 420 V, 3 ph, 50 Hz., induction weather proof with extended shaft and are specially designed for cooling tower application.

 

 

L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com 
Also visit us at our Facebook page

Timber Cooling Tower

Wooden Cooling Tower

Our wooden cooling tower has following features:

• Designed for maximum service life, dependability and performance.
• Readily adaptable for Industrial processes, D. G. Sets and Air conditioning.
• Maximum resistance against very hot temperatures and water borne contaminants.
• Consumes minimum power due to high efficiency F.R.P Axial Flow Fans.

Structure :
The structure of the cooling tower will be made from the best grade of pinewood pressure impregnated by chromate copper arsenate to prevent it from any bacterial attack.it is bolted and designed for 30pounds/sq. feet. Wind load efficiency.

Fans
Our cooling towers are fitted with FRP Axial Flow fans with Aerodynamic efficiency and significant saving in higher operating cost.

Fan Blades
Fan Blades are made up of fibre glass reinforced epoxy resins. These blades are hollow in construction and have been designed with most efficient aero foil section.

Optimum aero foil section thickness has been selected to achieve maximum lift and minimum drag coefficient. Twist is so designed that blade section are maintained at most efficient angle of attack having the highest lift drag ratio. Light and strong blades increase the life of mechanical drive arrangement.

Hub Assembly
Fan hub assembly is simply designed for easy installation and minimum maintenance. It is dynamically balanced and made of stainless steel plates, aluminum clamp blocks, cast iron bush and all hardware in stainless steel for resistance against corrosion.

Balancing of Fans
Fan Hub assemblies are dynamically balanced on Dynamic Balancing Machines and total Fan Blade assemblies are balanced on specially designed rig for vibration free continuous operation.

Fan Drive
Fans are directly driven by electric motors in small models and coupled through gearbox in larger models subject to the tip speed of the fan.

Fan Cylinder
Our cooling towers are fitted with elevated fan cylinders in HDG Steel or FRP material which enhance the air movement, completely eliminating the chances of re-circulation of exhaust air and thereby increasing cooling tower efficiency.

Hot Water Distribution System
The Hot Water Distribution System is of open Gravity type and is constructed from boiling water proof marine plywood with poly-propylene target nozzles.

Louvers and Casing
Corrugated asbestos cement board casing is applied vertically joints are lapped and sealed for water tightness. Corners are covered with FRP corner rolls. Corrugated asbestos louvers are located on wide centers on the sloping louvered walls. They are supported by tower columns and louver supports. ( FRP casing and louvers can be provide if desired.)

Internal Fills
Our cooling towers are fitted with “Foster Wheelers” stack type fill arrangement, comprising of splash bars fixed with transverse stringers making the fills into removable trays. This arrangement makes an excess to wet surface area and eliminates any chances of fill collapse. The splash bars and trays are made from As-Cu treated pinewood and are rectangular in cross-section.

Drift Eliminators
Specially designed eliminators are made in replaceable modules. Each module can be taken out easily, cleaned and put back into position in no time. Eliminates drift loss to less than 0.1%.

Cold water Basin & Other Works
The cold water RCC Basin is to be constructed by the purchaser, in accordance with the supplied drawings. The sting equipment, pumps, cabling,external piping are not included.

 Thank you

L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com

FRP Square Type Cooling Towers

Square Type Cooling Tower

Out cooling tower has following features:

• Must be for uniform water distribution and optimal heat transfer.
• Excellent resistance to corrosion can be achieved via fiber-reinforced plastic.
• These cooling towers must be compact and light in weight.
• These cooling towers must be easy to installation and maintain.

Our Square Type FRP Cooling Towers comprises of following parts:

Casing :
The tower casing is made of tough fibre-glass reinforced plastic (FRP) and has sufficient structure strength to withstand high wind velocities and vibrations. UV - stabilized resin is used along with gel coat for longer life.it is resistant to local impact and even if slight damage occurs, local repairs can easily be done. The portion of casing housing fill and eliminator has a round cross section. The water collection sump, also of FRP, is leak proof and avoids water spillage.
 

PVC Fills
The fill is of rigid Polyvinyl Chloride (PVC) and is of honeycomb design with very large contact surface area. The fill splits the air and water into several streams, increasing the time of contact and also heat transfer between water and air. The fill is in modules and is packed in the tower casing without ant cutting for curves. The air pressure drop through the fill is negligible. The fills are available with flute height of 12mm and 19mm with sheet thickness of 0.15 mm and 0.20 mm .

 

Sprinkler
Automatic rotary sprinkler system made of Aluminum alloy or cast steel material, with rotary head and sprinkler pipe distributes the hot water over the entire space of the filler. Sprinkler pipes are non-clogging, require low pressure to operate and assures uniform water flow with minimal operating pump head. The FRP eliminators attached to sprinkler pipe are specifically designed for low pressure drop and minimizes the drift loss of water.

  

Axial Fan
Specially designed energy efficient fans are of induced-draft axial type with adjustable pitch. Material chosen are non- corrosive of plastic, FRP or aluminum alloy. The high efficiency design ensures low running cost and the lowest possible noise level. Fan blade pitch is adjustable and dynamically balanced.

Motors
The motors are totally enclosed (IP55), Flange type , 420 V, 3 ph, 50 Hz., induction weather proof with extended shaft and are specially designed for cooling tower application.

We will be glad to have you valued inquiries. For more details and consulting on cooling towers please call us or drop us your mail.

Thank you

L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com

Leading Cooling Tower Manufacturers in India

Here I am pleased to mention that we have a wide range of Cooling Tower Manufacturers in India. Since 1947 India has built many industries like power plants, petroleum refineries, petrochemical plants, natural gas processing plants, food processing plants, semi-conductor plants. One of the industry is Cooling Tower Industry. The primary use of cooling towers is to remove the heat absorbed in the circulating cooling water systems used in the above mentioned industries and for other industrial facilities such as in condensers of distillation columns, for cooling liquid in crystallization, etc. I extent my article by mentioning the leading cooling tower manufacturers in India.

1) Paharpur

Paharpur has grown from a small lumber saw mill to one of the largest cooling tower manufacturers in the world. Paharpur have Research and Development centre which has consistently produced innovative concepts that have now become industry standards. Their engineering and production standards often exceed general standards, the objective being to supply a prime quality product which will provide low cost and reliable service to our customers over many years.

Industry they serve to:

• Electricity generating
• Petroleum refining
• Chemical processing
• Sugar
• Air-conditioning and
• Refrigeration
• Steel

2)  Wetpoint Aqua Equipments Pvt Ltd

Wetpoint Aqua Equipments Pvt. Ltd. is the largest manufacturer of cooling tower in central part of India. Our product range includes the Timber & FRP Induced Draught Cross flow & counter flow cooling towers which are designed and made as per particular process applications.

Wetpoint is in the business since 1996 and has professional approach towards system & documentation. Company policy is to design & manufacture the product to meet the requirement of the customer which would be able to delight him by good quality and better services.

They offers a wide range of cooling towers & spares for various applications like Air conditioning, DG sets, Compressors, Induction Furnace, Injection Molding Machines & various industrial processes. The capacities range from 5TR to 5000TR and the temperature ranges from 80 C to 30 C. We make use of all popular material like Double edge folded fill, FRP Fans, Plastic Sprinklers, PVC splash bars & Drift eliminators etc.

They have a long list of our satisfied customers all over India & abroad backed up with good after sales services WAEPL R&D Section is equipped with experienced engineers with advantage of AutoCAD & Pro-E. They are having experience in cooling tower technology, engineering assistance on basin construction, wiring piping and special cooling tower applications. Our experienced engineers has specialized knowledge to ensure a cooling tower selection that will produce optimum performance & economy for your exact need.

Whether you wish to cool the centralized air-conditioning plant of your building, dissipate heat from your processing plant or cool the water in your industrial complex, we at Wetpoint are at your service.

Industry they serve to:

• Electricity generating
• Petroleum refining
• Chemical processing
• Sugar
• Air-conditioning and
• Refrigeration
• Steel

3)  Mihir Cooling Tower

In pursuit of better and more efficient designs in FRP cooling towers, in 1992 Mihir Engineers Private Limited collaborated with the world leaders in this field – GEA Polacel of The Netherlands. The result of this collaboration was the rectangular shaped CM series counter flow type ‘Mihir Polacel FRP Cooling Towers’. These towers were manufactured using the latest technologies and computer based design techniques in engineering, over 18000 towers of various capacities are in operation in different fields of the industry.

Industry they serve to:

• Process Cooling
• Distillery
• Sugar Industry
• Power Plants

4)  North Street Cooling Towers (P) Ltd

North Street Cooling Towers (P) Ltd. was founded as a specialist in custom designed cooling towers for commercial and industrial purposes. The company has been at the forefront of the cooling tower industry since its inception in 1989. This has been possible due to great commitment to the company's goal, dedication for quality, united spirit for team work and working towards our aim for complete customer satisfaction. As we continue to meet the challenges of our customers for higher efficiency and greater volumes, we have developed our own manufacturing processes in our facility of 7200 sq.yards located in the National Capital Region, well equipped with all the latest machinery and highly trained workers to provide our customers with the best in the industry. We are constantly developing new and technologically innovative solutions for a dynamic industry where nature and technology converge.

Industry they serve to:

• Process Cooling
• Distillery
• Sugar Industry
• Power Plants

 

5)  PALTECH

PALTECH was founded in 1986 as a small Cooling Tower Manufacturing Company. With a dedicated and enthusiastic effort of Mr. H P Yadav, MD & CEO, the growth of the Company has been so rapid that today it is one of the leading manufacturers of Cooling Towers, Water Treatment Systems and Chilling Plants in the world.

The growth and expansion of the company took place simultaneously as the growing demand of customers had to be facilitated on a most priority basis. The company presently has an area of 1 Lac Sq.ft where huge manufacturing facility and a large warehouse have been established. This facility is located in Sohna, Haryana which has close proximity to Delhi as well as Gurgaon.

Industry they serve to:

• Process Cooling
• Distillery
• Sugar Industry
• Power Plants

Hope the above will be help full for your industrial needs.

Prahalad Rai
9669776202
RNB Infotech, Gwalior

Cooling Tower & Spares Manufacturer

Wetpoint Aqua Equipments Pvt. Ltd. is  the largest manufacturer of cooling tower in central part of India. Our product range includes the following:

1. Timber Cooling Tower
2. FRP Induced Draught Cooling Tower
3. FRP Cross Flow Cooling Tower
4. Counter Flow Cooling Tower 
5. Natural Cooling Towers
6. FRP Square Type Cooling Tower

Our designed cooling towers has the following characteristics:

• Designed for maximum service life, dependability and performance.
• Readily adaptable for Industrial processes, D. G. Sets and Air conditioning.
• Maximum resistance against very hot temperatures and water borne contaminants.
• Consumes minimum power due to high efficiency F.R.P Axial Flow Fans.
• Designed for uniform water distribution and optimal heat transfer.
• The special characteristic of fiber-reinforced plastic provide excellent resistance to corrosion.
• Our Cooling towers are compact and light in weight.
• Easy installation and maintenance.

We designed and made our cooling towers as per particular process applications. The primary purpose of cooling tower is to remove the heat from the circulating cooling water systems used that can be used in following industries:

• Power Plants
• Petroleum Refineries
• Petrochemical Plants
• Natural Gas Processing Plants
• Food Processing Plants
• Semi-Conductor Plants

Cooling Tower is also an essential machine for condensers of distillation columns, for cooling liquid in crystallization.

Besides this we also manufacture the spares for the cooling towers, no matter if it is a Timber Cooling Tower or FRP Cooling Tower. Our manufacturing range of cooling tower spares includes the following:

1. Cooling Tower Fan
2. Cooling Tower Motors
3. PVC Fills for Cooling Tower
4. Cooling Tower Sprinkler
5. Rubber Inserts for Cooling Tower
6. Louvers Casing for Cooling Tower
7. Water Distribution for Cooling Tower
8. Fan Cylinder for Cooling Tower
9. Water Flow Control Valve for Cooling Tower
10. 6Q Yoke for Cooling Tower
11. Gear Box for Cooling Tower
12. Drift Eliminator for Cooling Tower

We will be glad to have you valued inquiries. For more details and consulting on cooling towers please call us or drop us your mail.

Thank you

L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com 
 

We are the leading manufacturer of Industrial Cooling Towers in India

Wetpoint Aqua Equipments Pvt. Ltd. is the largest manufacturer of cooling tower in central part of India. Our product range includes the Timber & FRP Induced Draught Cross flow & counter flow cooling towers which are designed and made as per particular process applications.

Wetpoint is in the business since 1996 and and has been awarded the ISO 9001:2008 certification for approach towards system & documentation.

Company policy is to design & manufacture the product to meet the requirement of the customer which would be able to delight him by good quality and better services.

WAEPL offers a wide range of cooling towers & spares for various applications like Air conditioning, DG sets, Compressors, Induction Furnace, Injection Molding Machines & various industrial processes. The capacities range from 5TR to 5000TR and the temperature ranges from 80 C to 30 C. We make use of all popular material like Double edge folded fill, FRP Fans, Plastic Sprinklers, PVC splash bars & Drift eliminators etc.

We have a long list of our satisfied customers all over India & abroad backed up with good after sales services WAEPL R&D Section is equipped with experienced engineers with advantage of AutoCAD & Pro-E. They are having experience in cooling tower technology, engineering assistance on basin construction, wiring piping and special cooling tower applications. Our experienced engineers has specialized knowledge to ensure a cooling tower selection that will produce optimum performance & economy for your exact need.

WAEPL products are subjected to severe testing & quality checks before dispatch under various stages WETPOINT since inception has been working on focused and very clear objectives….. providing solution to customers working problems customized to their needs and continuous improvement on products & systems.

WETPOINT products are manufactured confirming to the following standards and technical specifications which are best in the industry and confirming to the Indian standards.

Thank you


L K Chatuvedi
CEO - Wetpoint Aqua Equipments (P) Ltd
Manufacturer of all kind of Industrial Cooling Towers
Phone: +91-9302.214.784
Email: ceo@wetpointcoolingtowers.com